Reviews on Edc15c11 Read write with kess, ktag, mpps, galletto

To read and write Bosch edc15c11 for a Volvo xc90 2.4d5 2005 model, which ecu programmer? how? what about kess, ktag, mpps etc?

1. MPPS: worked

Only boot mode
I’m did this ECU in boot with MPPS 

2. Kess V2 via bootmode: worked

I made a few of these ECUs from Kess V2 via bootmode without any problems.

Guide: Use the help files of ksuite… its easy…

3. fgtech galletto: worked

I read EDC15C11 just a few days ago with fgtech galletto

and used the diagram posted below:

No problem reading/writing. FYI, you have to make checksum before writing new file, since galletto does not support chksum correction on these ECUs

4. MPPS: worked too

Mpps in bootmode, use bosch generic protocol. Works fine done it several times.
Ore you can desolder chip and use a eprom programmer.
I had no sucsess with kess ore ktag. Ktag would only write backup, and not the 29f200 only.
I use ktag to make backup, and read and write 29f200 with mpps in bootmode.

5. fgtech galletto on boot mode… very easy.

Read documents boot mode fgtech…

 

Good luck!

How to read Kia kefico m7.9.8 with trastata, Ktag and FGTech?

Have Kia kefico m7.9.8 to read the ECU pinout boot mode or BDM, need Ktag, FGTech, transdata.This article is available with how to read FGTECH and how to read with transdata and Ktag etc.

1. Read Kia kefico m7.9.8 with FGTech, here is a tutorial

http://blog.obdexpress.co.uk/2017/08/08/fgtech-galletto-v54-100-readwrite-bosch-mg-7-9-8/

2. Read Kia kefico m7.9.8 with transdata and Ktag, here is a tutorial.

BOSCH_M798_KIA
The LAY by pins are located on the lower part of the ECU
PLUGIN 167


Connect the power (+12v) only for DIRECT CONNECTION,
do not connect power (+12V) with DIMA CONNECTION

DIRECT CONNECTION
Connect the universal wiring to POL4 & POL5 and to the ECU connector as shown in the pictures.


DIMA CONNECTION
Connect the blue wire to POL5 and to DIMA adapter as shown in the picture.


I would advise using pencil, it is always faster, comfortable and clean to work.


From http://www.obdexpress.co.uk/wholesale/bdm-frame-cmd-bdm100-fgtech-kess-ktag.html


http://blog.obdexpress.co.uk/2019/07/30/how-to-read-kia-kefico-m7-9-8/

KTAG Reads Bosch ME 9.7 from Mercedes S350 (W221) 2006

Can use ktag ecu programmer to work on ME 9.7 Mercedes S350 2006? How to do ?

Here we go:
Test: Ktag on ME 9.7 Mercedes S350 2006
Tool: Ktag programming tool China clone
Car: Mercedes S350 (W211) 2006
ECU: Bosch ME 9.7

Procedure:
Select a model in KTag software

IMPORTANT: make a backup copy of the ECU
Connect the ECU to the Ktag programmer
Pin 2 = GND
Pin 15, 16 = +12V

Ktag is gonna to read Bosch Me 9.7 Mercedes (P102)

Success! Then save data.

Result: Ktag can read Me 9.7 Mercedes without any issue!


Src:
http://www.obdexpress.co.uk/service/how-ktag-reads-me-97-mercedes-s350-w221-2006-29709.html